Page 1 of 1

How to install one thermostat?Is there anyone use it ?

Posted: Tue May 05, 2015 8:23 pm
by lerway
How to install one thermostat(temperature controller)?Is there anyone use it for home brew .The device information like following:

Detailed Product Description
Measure range:-50~+99°C
Mounting size:71*29mm
Auto switch between refrigerating and heating
Retrun difference value
All-purpose Temperature Controller STC-1000:

Features:
Switch the modes between cool and heat; Control temperature by setting the temperature setting value and the difference value; Temperature calibration; Refrigerating control output delay protection; Alarm when temperature exceeds temperature limit or when sensor error.

Specification and Size:
1.Front panel size75(L)×34.5(W)mm;
2.Mounting size:71(L)×29(W)mm;
3.Product size75(L)×34.5(W)×85(D)mm;
4.sensor length2minclude the probe.

Technical Parameters:
1. Temperature measuring range: -50~99oC;
2. Resolution: 0.1°C; 3. Accuracy: ±1°C (-50~70°C);
4. Sensor error delay: 1 minute
5. Power supply: 110VAC±10%, 50/60Hz;
6. Power consumption: ≤3W;
7. Sensor: NTC sensor (1PC);
8. Relay contact capacity: Cool 10A/250VAC;Heat 10A/250VAC;
9. Ambient temperature: 0~60°C;
10.Storage temperature: -30~75°C;
11.Relative humidity: 20%~85% (No condensate).

Re: How to install one thermostat?Is there anyone use it ?

Posted: Wed May 06, 2015 7:59 am
by Ross Robotics
What do you mean install it? Do you mean how to connect it to a controller?

Re: How to install one thermostat?Is there anyone use it ?

Posted: Wed May 06, 2015 7:06 pm
by lerway
codlink wrote:What do you mean install it? Do you mean how to connect it to a controller?

Oh ,yes ,I don;t know how to connect it.

Re: How to install one thermostat?Is there anyone use it ?

Posted: Thu May 07, 2015 5:36 am
by n1ist
Look at the side of the STC-1000; the picture describes the connections. Also, do a google search for "STC-1000". There are many hits. This one http://brewprof.com/weekend-diy-homebre ... -stc-1000/ shows how to mount the controller in a box with two controlled outlets on the output.
This thread http://www.homebrewtalk.com/showthread.php?t=330427 goes into details on how to add relays to power larger loads.
/mike

Re: How to install one thermostat?Is there anyone use it ?

Posted: Fri May 08, 2015 12:24 am
by lerway
n1ist wrote:Look at the side of the STC-1000; the picture describes the connections. Also, do a google search for "STC-1000". There are many hits. This one http://brewprof.com/weekend-diy-homebre ... -stc-1000/ shows how to mount the controller in a box with two controlled outlets on the output.
This thread http://www.homebrewtalk.com/showthread.php?t=330427 goes into details on how to add relays to power larger loads.
/mike
:clap: :clap: :clap:

Thank you so much !

Re: How to install one thermostat?Is there anyone use it ?

Posted: Thu May 14, 2015 8:52 pm
by lerway
This videos tell us how to connect one PID temp. controller but I'd like to know how to connect one ITC-1000F

https://youtu.be/DZDkrR0Vhrc

Re: How to install one thermostat?Is there anyone use it ?

Posted: Fri May 15, 2015 12:17 pm
by DanV

Re: How to install one thermostat?Is there anyone use it ?

Posted: Thu May 21, 2015 10:43 pm
by lerway
DanV wrote:The manual tells all:
http://www.ink-bird.com/asset/file/ITC-1000F_EN.pdf
Thank you.