RESOLVED - DRC Bot not sending me results

Questions about the BatchPCB service

Moderators: phalanx, robacarp

Locked
PhracturedBlue
Posts: 10
Joined: Sun Jun 26, 2005 6:35 pm

RESOLVED - DRC Bot not sending me results

Post by PhracturedBlue » Sun Jul 23, 2006 8:44 am

I am trying to get 2 board designs uploaded.
The 1st went through fine, and I got an email within 5 mins saying everything was ok.
The 2nd (which is slightly larger) goes through the 1st 3 steps, but I never get an email back (tried 3 times over the course of a day with slight alterations each time). This implies that something is wrong with the board, But I have no idea what it is as I am not getting any feedback.
Board drawn in Eagle 4.16r1, all width/spacing >= 10mil, drd is 2.4, through-hole components, everything has been verified in ViewMate as aligned, 1.6"x1.8"
Last edited by PhracturedBlue on Tue Jul 25, 2006 5:37 pm, edited 1 time in total.

PhracturedBlue
Posts: 10
Joined: Sun Jun 26, 2005 6:35 pm

Re: DRC Bot not sending me results

Post by PhracturedBlue » Mon Jul 24, 2006 7:49 am

PhracturedBlue wrote: Board drawn in Eagle 4.16r1, all width/spacing >= 10mil, drd is 2.4, through-hole components, everything has been verified in ViewMate as aligned, 1.6"x1.8"
I did some further experimentation, and if I send the top layers+drill or bottom layers+drill it goes through fine. As soon as I include both the component and solder layers at the same time, it doesn't send me an email.

User avatar
sparky
Site Admin
Posts: 1337
Joined: Mon May 05, 2003 6:02 pm
Location: Colorado
Contact:

Post by sparky » Mon Jul 24, 2006 12:35 pm

DRC Bot is up and running. Check your spam filters. Because we send jpg attachments, we get spam canned.

Let me know if you're still having problems and I'll try to dig out the emails.

-Nathan
Pursue the cheese, win the excellence.

PhracturedBlue
Posts: 10
Joined: Sun Jun 26, 2005 6:35 pm

Post by PhracturedBlue » Mon Jul 24, 2006 4:16 pm

sparky wrote:DRC Bot is up and running. Check your spam filters. Because we send jpg attachments, we get spam canned.

Let me know if you're still having problems and I'll try to dig out the emails.

-Nathan
I have double checked that I never received emails for this design. As I said in my previous post, I receive an email if only the top layer or bottom layer is sent, but not if both are sent. BatchPCB account is on the same e-mail address that I am registered under here, but if you need more specifics, please let me know.

PhracturedBlue
Posts: 10
Joined: Sun Jun 26, 2005 6:35 pm

Post by PhracturedBlue » Tue Jul 25, 2006 5:37 pm

PhracturedBlue wrote:
sparky wrote:DRC Bot is up and running. Check your spam filters. Because we send jpg attachments, we get spam canned.

Let me know if you're still having problems and I'll try to dig out the emails.

-Nathan
I have double checked that I never received emails for this design. As I said in my previous post, I receive an email if only the top layer or bottom layer is sent, but not if both are sent. BatchPCB account is on the same e-mail address that I am registered under here, but if you need more specifics, please let me know.
I'm sorry for being an idiot. My mail forwarding service was dropping the emails because they were too big due to the attached images (the simple boards went through, the complex ones didn't). I changed my email address, and everything is fine now.

I appologize for my mistake.

Locked