SparkFun Forums 

How to get assistance from a SparkFun Technical Support moderator.
by TS-John  - Tue Mar 05, 2019 10:27 am  - in: How to get Technical Assistance from a Technical Support Moderator

BatchPCB question...
by MarkS  - Sun Sep 30, 2007 4:55 pm

Generating Gerbers through automation
by mzoran  - Wed Sep 26, 2007 9:35 am

0.4mm pad spacing + 8 mil restriction?
by pellepl  - Tue Sep 25, 2007 8:27 am

Net labels?
by bryon  - Tue Sep 18, 2007 8:05 pm

Hand soldering the SCP1000 Pressure sensor
by silic0re  - Fri Sep 14, 2007 8:42 am

Board optimization
by Chupa  - Sun Sep 09, 2007 9:40 am

SFE Library and part prefixeses
by Andrew02E  - Tue Sep 11, 2007 11:56 am

Ground Poly to Border Spacing
by slide  - Sun Sep 09, 2007 10:55 pm

Printer Gerber and Exellon files
by rr_pilot  - Wed Aug 29, 2007 2:25 pm

Eagle error: Unknown object type
by jandirks  - Fri Aug 31, 2007 7:17 am

min. / max. length for sdram signals
by saoirse  - Wed Aug 29, 2007 7:51 am

Clearance/width troubles

• 1
• 2

by jandirks  - Tue Aug 21, 2007 3:33 am

Ever managed to get an MLF32 chip in your PCB design?
by jandirks  - Thu Aug 23, 2007 7:16 am

Thank you, David Carne!
by Tom2000  - Fri Aug 17, 2007 2:49 pm

Missing silkscreen shapes
by null  - Mon Aug 06, 2007 5:51 pm

large smt pads in Eagle
by rocketbob  - Tue Jul 31, 2007 3:24 pm

Eagle SMD layers
by Chupa  - Sun Aug 12, 2007 3:08 pm

Rounded corners
by richas  - Thu Jul 19, 2007 12:34 pm

SMD QFP in 'smd-ipc' library fails DRC?
by silic0re  - Tue Jul 31, 2007 10:06 pm

components flying off board when reflowing in toaster oven
by t9corp  - Mon Jul 30, 2007 9:50 am

using GerbMerge.. can't get paste the DOS
by ghsrocketman  - Thu Jul 26, 2007 11:19 pm

How small can I make a PCB
by roacan  - Wed Jul 18, 2007 5:15 am

EAGLE: connect an IC to traces on one side only
by cfinger  - Thu Jul 12, 2007 7:29 am

Current plane?
by Bergamot  - Thu Jul 12, 2007 1:36 pm

tango
by FireFly  - Tue Jul 03, 2007 8:25 am

Should I be able to see via holes in BATCHPCB preview image?
by mhough  - Sat Jun 30, 2007 3:41 pm

Design failed DRC
by denisbest  - Thu Jun 21, 2007 9:46 pm

Bottom copper layer solid but should not be
by Racer1  - Fri Jun 22, 2007 7:38 pm

Grounded Guard Ring
by Chupa  - Wed Jun 20, 2007 8:26 pm

via with no solder mask
by RonnyM  - Thu Jun 14, 2007 1:24 pm

Problems getting from schematic to board
by jandirks  - Fri Jun 15, 2007 2:57 pm

Creating complex pads
by Lucien  - Mon Jun 11, 2007 2:16 pm

Clearence

• 1
• 2

by CommanderBob  - Fri Jun 01, 2007 11:03 pm

accelerometer
by Ralph  - Thu Jun 14, 2007 1:43 pm

Surface Mount Package
by deek  - Mon Jun 04, 2007 12:27 pm

PICAXE Library
by b_w_  - Mon Jun 04, 2007 5:31 pm

Creating an Eagle library from an existing schematic
by trialex  - Sun May 27, 2007 6:15 pm

Where to get 0402 Caps and Inductors

• 1
• 2

by slide  - Thu May 24, 2007 5:14 pm

Eagle help
by slide  - Fri May 25, 2007 1:08 pm

PADS Conversion Required
by secureoffice  - Mon May 28, 2007 12:56 pm

DIY Soldermask/resist
by Chip Douglas  - Wed May 16, 2007 7:12 am

Temporary files?
by tracebender  - Sat May 19, 2007 9:55 am

Eagle Footprint
by slide  - Wed May 16, 2007 1:29 pm

Manual routing and net classes
by tracebender  - Thu May 17, 2007 3:46 pm

Eagle Question about supply circuits.
by propellanttech  - Thu May 17, 2007 10:34 am

smt parts on bottom layer
by thegruffalo  - Sun May 13, 2007 7:37 am

Part clearance
by futrtrubl  - Tue May 08, 2007 2:04 am

Thanks SparkFun!!
by gussy  - Tue May 08, 2007 3:45 am